Compatible Systems MicroRouter 900i Instrukcja Użytkownika Strona 4
- Strona / 94
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4 - Contents Microrouter CNC Machine User's Manual
Contents
Section 6: Work Holding
The Work Holding Clamp Rail Components..................................40
Assembling the Work Holding Clamp Rails ...................................41
Using the Work Holding Clamp Rails.............................................43
The Vacuum Table Components ...................................................44
Preparing the Microrouter Working Area .......................................45
Fitting and Using the Vacuum Table ..............................................46
Section 7: Maintenance
Maintenance Schedule and Charts ...............................................48
General Work Area Cleaning.........................................................49
Lubrication Areas on the Microrouter ............................................50
Lubrication of Leadscrews.............................................................51
Lubrication of Sliderails .................................................................54
Cleaning the Thrust Bearing Couplings.........................................57
Cleaning the Datum Microswitches ...............................................58
Laminate Trimmer Maintenance....................................................61
Section 8: Machine Electronics
Accessing the Electrical Panel ......................................................62
Layout of the Electrical Panel........................................................63
The Denstep Motion Control Board ...............................................64
The Spindle Drive Board ...............................................................65
Section 9: Technical Support
Technical Support..........................................................................66
Troubleshooting.............................................................................67
Section 10: Appendix
Specification of Microrouter CNC machine....................................70
What is a Part Program? ...............................................................71
Composition of a Part Program .....................................................72
G Codes List .................................................................................73
M Codes List .................................................................................74
List of Program Address Characters .............................................75
Denford Directives.........................................................................76
Understanding Offsets...................................................................78
Configuring a Workpiece Offset.....................................................80
Configuring a Tool Length Offset...................................................81
EC Declaration of Conformity........................................................83
Microrouter Series Noise Level Test Results.................................85
Section 11: Glossary
Glossary ........................................................................................87
Section 12: Index
Index .............................................................................................91
- Microrouter 1
- CNC Machine 1
- User's Manual 1
- Contact Information 2
- Contents 3
- Warning Notices 5
- About this Manual 6
- 1: What is CNC? 8
- Safety Features Overview 10
- Safety Precautions 10
- 3: Levelling your Microrouter 16
- 3: Electrical Diagrams 17
- Dust Extraction Systems 20
- 9 to 25 Pin D 22
- Serial Cable* 22
- (see Note * left) 23
- Lefthand and Rear 24
- Cabinet Layout 24
- Front Cabinet 24
- 4: Part Manufacture 29
- Checklist and Tool Changing 29
- 5: Performing a Tool Change 32
- Machine Head 34
- Removing a Tool 36
- Refitting a Tool 36
- Vacuum Table Troubleshooting 47
- Lubrication Chart 48
- Maintenance Schedule 48
- 7: General Work Area Cleaning 49
- 7: Lubrication of Leadscrews 51
- 7: Lubrication of Sliderails 54
- X Axis Datum Microswitch 58
- Y Axis Datum Microswitch 59
- Z Axis Datum Microswitch 60
- Failure to Start 61
- Lubrication 61
- Brush Inspection 61
- Display 64
- 8: The Spindle Drive Board 65
- 9: Technical Support 66
- 9: Troubleshooting 67
- 10: What is a Part Program? 71
- Part Program example 72
- 10: G Codes List 73
- 10: M Codes List 74
- 10: Denford Directives 76
- 10: Understanding Offsets 78
- The cutting tip 82
- EC Declaration of Conformity 83
- 11: Glossary 87
- 12: Index 91
- 12: Notes 93
Powiązane produkty i podręczniki dla Networking Compatible Systems MicroRouter 900i
(8 strony)
(2 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji